JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY
vol.38 no.435 April 1997
---CONTENTS---
Essay
- Role of our Society with Fundamental Law of Science and Technology
Hisashi NISHIMURA
PAGE I (303)
Explanations
- Industrial Application of DLC Coatings for Plastic Working Tools
Tai KUMAGAI
PAGE 2 (304)
- Structural Optimization Based on the Topology
Keizo ISHII
PAGE 7 (309)
- Laser Processing in Electronic Components
Recent Developments of Micromachining Technology II
Yukio NISHIKAWA, Toshiharu OKADA and Yoshikazu YOSHIDA
PAGE 12 (314)
- 3D Actuators by Adding Functional Films
Recent Developments of Micromachining Technology III
Hiroshi OGURA and Yoshikazu YOSHIDA
PAGE 18 (320)
Preface
- At the Beginning of a New Series "Plastic Working Laboratories in the World"
.Editorial Committee
PAGE 23 (325)
Lounges
- Days in The Ohio State University as Visiting Scholar
Naozumi HATADA
PAGE 24 (326)
- "Young Member's Meeting" Established by Planning Committee of JSTP
Masaru OKADO, Takashi ARIIZUMI and Toshihiro IMAI
PAGE 26 (328)
Mail from Branches and Local Committees
- Report from Chugoku-Shikoku Branch of JSTP
Shunichi KAWANO
PAGE 28 (330)
Papers
- Effects of Pressure Distribution and Boundary Condition on Deformation Mechanism of a Circular Metal Plate Subject to Shock Pressure
Masahiro FUJITA, Yasuo ISHIGORI, Minoru MOCHIHARA,Hiroo OSAKA, Rui ZHANG and Hirofumi IYAMA
PAGE 29 (331)
- Analysis of Circular Tube Bending by MOS Bending Method
Makoto MURATA
PAGE 35 (337)
- Plastic Flow of a Metal Plate in the Shearing Process under Shock Pressure
Minoru MOCHIHARA, Masahiro FUJITA, Yasuhiro NAKIYAMA,Kazuyuki H0KAMOTO and Shigeru ITOH
PAGE 40 (342)
- Fuzzy Adaptive Control of Circular-Cup Deep-Drawing Process Using Variable Blank Holder Force Technique
Shoichiro YOSIHIARA, Ken-ichi MANABE, Ming YANG and Hisashi NISHIMURA
PAGE 46 (348)
- Method for Calculating Punch Stroke-Punch Load Curves in Deep-Drawing Irregularly Shaped Cylindrical Shells with Arbitrarily Shaped Flanges
Wen-hua SI Toshihiko KUWABARA and Masayuki SHUUNO
PAGE 52 (354)
- Powder Forging of Combined Al-Si Alloy Powder and I/M Alloy
Nobukazu HAYASHI
PAGE 58 (360)
- Consideration on the Relationship Between Breakthrough and Noise During Press Blanking
Jianhua Mo, Masao KONDOH, Nobuhiro KOGA and Masao MURAKAWA
PAGE 65 (367)
- Experiment on Rectangular Cup Drawing of Sheet Metal
Takaji MIZUNO and Daixin O
PAGE 70 (372)
- Synthesis of Ti-Al Intermetallic Compounds by Pressure Infiltration
Tohru SHIROTA, Tasuku DENDO, Kenki HASHIMOTO, Haruo DOHI,Takashi KIMURA and Morihiko NAKAMURA
PAGE 75 (377)
Note
- Development of an Assembly for Hot Dynamic Compaction of Powders Using a Converging Underwater Shock Wave
Kazuyuki HOKAMOTO, Seiichiro TANAKA, Takahiro KUGIMOTO,Masahiro FUJITA, Shigeru ITOH and Akira CHIBA
PAGE 80 (382)