JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY
vol.38 no.432 January 1997
---CONTENTS---
Prefaces
- For Human Ability Extension and Advanced Manufacturing,
at the Occasion of Revising "SOSEI-TO-KAKOU" to A4 Size
Toshiro FUJIWARA
PAGE 1 (1)
- On the Size Change of this Journal
Kazuyoshi KONOO
PAGE 1 (1)
Essay
- Encouragement of Manufacturing Industries in Japan
Toru KONDO
PAGE 2 (2)
Prefaces
- Enlargement of our Journal of J. S. T. P.
"Journal of J. S. T. P" Committee
PAGE 3 (3)
- Thirty Fifth Anniversary At a Publication of "Roots of Japan Society for Technology of Plasticity
Editorial Committee
PAGE 3 (3)
Round-Table Talks
- Thirty Five Years Development of Japan Society for Technology of Plasticity
Hiromu SUZUKI
PAGE 4 (4)
- Roots of Japan Society for Technology of Plasticity
Junji KIHARA, Yasuo KASUGA, Toshio IKEJIMA, Koichi SAITO, Hideaki KUDO and Yasuhisa TOZAWA
PAGE 8 (8)
********* Minor Special Issue on New Processes in Sheet Metal Forming *********
Essay
- Analog or Digital? - Hegemony over Metal Working -
Yutaka HAYASHI
PAGE 22 (22)
Review
- Recent Trends in Sheet Metal Forming
Katsuhiko YAMAGUCHI
PAGE 23 (23)
Explanations
- Press Formability of Stainless Steels
Seishi ISHlYAMA
PAGE 28 (28)
- Formability of Surface-Coated Sheet Steels
Toshiyuki KATO
PAGE 35 (35)
- Deformation Behavior of Laminated Sheet Metals
in Bending and Press-Forming
Matsuo USUDA and Koji HASHIMOTO
PAGE 40 (40)
- Press Forming of Tailored Blanks
Fumiaki NATSUMI and Masahiro OHARA
PAGE 45 (45)
- Stretch Draw Forming of Laminated Sheet
Katsuhiro IMAZU
PAGE 52 (52)
- Combined Process of Sheet Metal Forming in Electric Products
Hiroya MURAKAMI
PAGE 57 (57)
Preface
- At the Beginning of a New Series "Fundamentals of Sheet Metal Forming"
Editorial Comittee
PAGE 63 (63)
Lecture
- Material Properties and Formability Tests of Sheet Metals
Katsuhiko YAMAGUCHI
PAGE 64 (64)
************************************************************************************
Papers
- Simulation of Strip Crown in Cross Rolling
- Analysis of Strip Crown by Rigid-Plastic FEM in Cold Rolling ll -
Hideaki FURUMOTO, Kazuo MORIMOTO, Kanji HAYASHI and Kozo OSAKADA
PAGE 71 (71)
- Deformation Analysis of a Three-Roll Reducing Mill
Tatsuya OKUL Masayuki YAMADA and Tateo YAMADA
PAGE 76 (76)
- Surface Finish by Multi-stage lroning of Extruded Aluminum Pipe
- Improvement of Formability in lroning of Extruded Pipe
and 3 Dimensional Analysis of_ Surface Roughness -
Teruie TAKEMASU, Tatsuo OZAKI, Ryoichi MATSUNAGA,
Susumu YAMAZAKI, Masashi SAKAGUCHI and Minobu SUKIMOTO
PAGE 81 (81)
- Influence of Punch Shape on Change of Sectional Shape on Dieless Shearing of Section
- Research on Shearing of Extruded Section by Low-Cost Die lll -
Hidetaka KIDA, Norio TAKATSUJI, Mitsugu TOKIZAWA,
Kenji MATSUKI, Kazuo MUROTANI and Nobushige DOGUCHI
PAGE 87 (87)
- Accuracy of Determination of Three-Dimensional Coordinates and Strain of Press
Formipg Products by Image Sensing Camera
Makoto SAKAMOTO Takao SAWADA and Yukio SHINOZUKA
PAGE 92 (92)