JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY
vol.37 no.431 December 1996
---CONTENTS---
Essay
- Essay
Shigeo MATSUBARA
PAGE 1237
Explanations
- Three-Dimensional Forming of Micro-Components by Shearing Processes
Isamu AOKI and Toshinori TAKAHASHI
PAGE 1238
- Numerical Material Testing and Plastic Working Analysis Using Finite Element Polycrystal Model
Hiroshi YANO
PAGE 1252
- Improvement in Accuracy of Bourdon Tube by the Precise Plastic Working
Hiroshi FURUKAWA
PAGE 1260
- Relation between Working Conditions and Qualities on the Forming of Bourdon Tube
Hiroshi FURUKAWA
PAGE 1267
- Analytical Methods of Incremental Forming of Sheet Metal
Hideo ISEKI
PAGE 1276
- A Series of "Recent Topics on Length Measurement" XI
Measurement of Civil Structures Using CCD Cameras
Kunio TORII, Yoshitaka KOZAKURA and Koji TAKADA
PAGE 1283
Mail from Branches and Local Committees
- Recent Activities in JSTP Kansai Branch
Katsuhiko YAMAGUCHI
PAGE 1290
Papers
- Development of Compressive Torsion Forming for Consolidation of Metal Powder
Eiji MAEDA, Naoyuki KANETAKE and Takao CHOH
PAGE 1291
- Improvements in Superplastic Forging Abilities of Titanium Alloys by Adding a Cold-Pre-Deformation
--- Development of Watch Case Made of Titanium Alloy IV ---
Isao KUBOKI, Keitaro KOROISHI, Yoshinobu MOTOHASHI and Mitsuji HIROHASHI
PAGE 1297
- Deformation Analysis of ERW Pipes Subjected to 2-Roll Sizer
--- Improvement of Pipe End Roundness for Thin Wall Pipes III ---
Yoshiaki ITAMI and Matsuo ATAKA
PAGE 1303
- Fundamental Nature of Tension Leveling
Fumio HIBINO
PAGE 1309
- Fundamental Study on Clearance Compensation Effect and Side FOrce in Shearing
Isamu AOKI, Toshinori TAKAHASHI, Hiromu SAITOH, Akira GOTOH and Koto SAKAMOTO
PAGE 1316
- Analysis of Stress Distribution and Width Narrowing in Hot Strip Rolling Using BOundary Element Method
Masashi TSUGENO, Makoto MIYASHITA, and Junji KIHRA
PAGE 1322
- Multi-Billet Extrusion Characteristics of Zirconia/Stainless Steel Two-Layer Pipes
Zhongchun CHEN, Tadasu MURAKAMI and Akitake MAKINOUCHI
PAGE 1334
- Effects of Rolling Conditions on Surface Brightness of Rolled Strips in Pair Cross Cold Rolling
--- Surface Brightness of Rolled Strips in Pair Cross Cold Rolling I ---
Hideo YAMAMOTO, Atsushi TOMIZAWA, Toru KANEKO, Tetsuo KAJIHAEA, Hideaki FURUMOTO and Kanji HAYASHI
PAGE 1340
- Development of Highly Accurate Bending System with Bend Angle Sensor
Toshihiko OENOKI, Toshio OTANI and Masaaki TAKADA
PAGE 1346
- Curling Analysis of Stretch-Bent-Unbent Sheet Metal
--- Springback Analysis of Sheet Metal II ---
Toshihiko KUWABARA, Susumu TAKAHASHI and Kenji ITO
PAGE 1352
- Experimental Verification of Culing Analysis of Stretch-Bent-Unbent Sheet Metal
--- Springback Analysis of Sheet Metal II ---
Manabu KIUCHI and Sumio SUGIYAMA
PAGE 1360
- Development of Numerical Simulation Model for Foming Loop Spline
--- Spline Rolling of Rolling of Deep Drawn Cups II ---
Ryoichi MATSUNAGA, Tatsuo OZAKI, Teruie TAKEMASU, Ryuzo KAMASHITA and Hidehiko TSUKAMOTO
PAGE 1367