JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY
vol.37 no.430 November 1996
---CONTENTS---
Essay
- Genuine Technology
Matsuo ATAKA
PAGE 1117
Explanations
- Application States and Problems of Rolling Analysis by Finite-Element Method
Ikuo YARITA, Hirotaka KANO and Takaaki IGUCHI
PAGE 1118
- Forming Limit of Sheet Metal Laminates
Fusahito YOSHIDA and Ryutaro HINO
PAGE 1125
- Application and Future of FEM Simulation for Press Forming
Koichi KAZAMA
PAGE 1131
- Rapid Prototyping of Metallic Models
Fumie ABE and Kozo OSAKADA
PAGE 1137
Lounge
- Academic Society as a Source of Technological Information
Hiroshi IKE
PAGE 1143
Technological Development
- Development of Press Die Made of Concrete
Masao WATANABE and Akihiko KOJIMA
PAGE 1145
Mail from Branches and Local Committees
- Activities in JSTP Niigata Branch
Osamu SAKAI
PAGE 1147
Papers
- Characteristics of Coefficient of Friction under High Pressure
--- Tribology in Sheet Metal Forming I ---
Akira AZUSHIMA, Taisuke UCHIDA, Kiyoshi IMAI and Hifumi YAMAGISHI
PAGE 1149
- Generation of Various Curves and Slitting of Aluminium Thin Sheet along the Curves
--- Flexible Sheet Metal Processing with Rolls and Piano Wires I ---
Norio TAKAKURA, Nobuhiko SHIRAKAWA, Shoji IMATANI and Katsuhiko YAMAGUCHI
PAGE 1155
- Pseudo-3-Dimensional Analysis of Shape and Crown in Flat Rolling by the Rigid-Plastic Model
--- Generalized 2-Dimensional Theory for Pseudo-3-Dimensional Analysis of Flat Rolling I ---
Hiromi MATSUMOTO and Shuichi HAMAUZU
PAGE 1162
- Lateral Material Flow Model for Use in the Pseudo-3-Dimensional Analysis of Flat Rolling
---Generalized 2-Dimensional Theory for Pseudo-3-Dimensional Analysis of Flat Rolling II ---
Hiromi MATSUMOTO and Kenji YAMADA
PAGE 1168
- Forward-Backward Extrusion with Axially Driven Container
Kozo OSAKADA, Xin WANG and Shinji HANAMI
PAGE 1174
- Finishing of Metal Mould for Free-Form Surface Using Elastic Polishing Tool
Isamu AOKI, Kiyoshi SUZUKI and Tetsutaro UEMATSU
PAGE 1180
- Examination of Working Limitation for Change of Sectional Shape on Dieless Shearing of Section
--- Research on Shearing of Extruded Section by Low-Cost Die II ---
Hidetaka KIDA, Norio TAKATSUJI, Mitsugu TOKIZAWA, Kazuo MUROTANI and Kenji MATSUKI
PAGE 1187
- Influence of Surface Defects on Bulge--Forming Limit of Aluminum Thin-Walled Tube
Tetsumaro HIROI and Hisashi NISHIMURA
PAGE 1193
- Development of Three-Dimensional Microcomponent Forming Press Machine
--- Trial Die Forming of Three-Dimensional Microcomponent from Round Wire and Development of Exclusive Press Machine ---
Isamu AOKI, Toshinori TAKAHASIJI, Haruya UENO and Toshiro HIGUCHI
PAGE 1199
- Application of an On-Line Pass Schedule Calculation Based on Roll Force Ratio Distribution
Masashi TSUGENO, Kunio SEKIGUCHI and Yoshiharu ANBE
PAGE 1207
- A New Method to Measure Solid Fraction of Mushy/Semi-Solid Metals and Alloys
Manabu KIUCHI and Sumio SUGIYAMA
PAGE 1213
- Mashy-State Forging of Cast-Iron
Manabu KIUCHI, Sumio SUGIYAMA and Masao ARAI
PAGE 1219