JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY
vol.43 no.502 November 2002
---CONTENTS---
*************Minor Special Issue on Rotary orming Technology*************
Essay
- Expectancy of Rotary Forming
Atsushi DANNO
Page 1(1023)
Explanations
- Recent Trends in Rotary Forming Processes
Ken-ichi KAWAI
Page 2(1024)
- New Rotary Forming Technology inJapan
Yoshiaki TAKADA
Page 8(1030)
- Trends and Apprications of Rotary Forming Technologies for Automotive Industries
Tomoyuki HIROTA
Page 13(1035)
- Thermo-Mechanical Treatment with Hot Form-Rolling for High Strength Gears
Toshiaki TANAKA
Page 19(1041)
Data
- Subjects and Applications in Recent Sponning Technology
Saburo NISHIYAMA
Page 24(1046)
************************************************************************************
Papers
-
An Approximation Model of Contact State between Roll and Strand
-- Computation of Three-Dimensional Deformation Behavior of Continuously Cast Steel Strand in Multiroll Spans 1 --
Shiro TOYOSHIMA, Manabu GOTOH and Kiminori NAKAYAMA
Page 29(1051)
-
Prediction of Bulging by Approximation Model of Contact State between Roll and Strand
-- Computation of Three-Dimensional Deformation Behavior of Continuously Cast Steel Strand in Multiroll Spans 2 --
Shiro TOYOSHIMA, Manabu GOTOH and Kiminori NAKAYAMA
Page 34(1056)
-
Method of Calculating Load and Torque in the Rolling of Lumber Using the Stress-Strain Curve Obtained by Uniaxial Compression
-- Studies on the Rolling of Wood 2 --
Keisuke YAMAGUCHI, Hiroyuki SHIOZAKI,
Tadahiro KAWASE and Tadao MUROTA
Page 39(1061)
-
Evaluation of Springback Analysis Accuracy for Stretch-Bending Simulation Using Four-Node Shell Element
-- Springback Simulation Using the Static Explicit FEM Code,
Using a New Algorithm for Canceling Nonequilibrated Forces 2 --
Naoto YAMAMURA, Toshihiko KUWABARA,
Akitake MAKINOUCHI and Cristian TEODOSIU
Page 44(1066)
-
Deformation Behavior of Al-Si-Fe Alloy Powder during Powder Forging Process
Toshikatsu KOIKE, Hiroshi YAMAGATA and Naoyuki KANETAKE
Page 50(1072)
-
Tensile Properties and Press Forability of a Mg-9Li-1Y Alloy Sheet
Hirohiko TAKUDA, Shiomi KIKUCHI,
Noriyuki YOSHIDA and Haruo OKAHARA
Page 55(1077)
-
Theoretical Solution for Allowable Minimum Wrap Angle of Strip Coil to Avoid Loosening against Expansion Force from Mandrel
Keiji MIZUTA and Tadashi NAKAGAWA
Page 60(1082)
-
Effect of Forming Conditions on Cross-Sectional Shapes of Corners of Square Steel Pipes Formed by Draw Bench Method
Xin GUAN, Yoshitomi ONODA, Eiji WAKAMATSU,
Sadao KIMURA and Takeo KITAWAKI
Page 66(1088)
-
Design of Die Depended upon the Variation of Product Size and of Material Strength
-- Research on Box-Shaped Reinforced Bumper Made of High-Strength Steel Sheet 2 --
Motoo ASAKAWA, Isao KUWAYAMA, Takayuki HAMA,
Hiroyuki HOSODA, Yoshio FUJISHIRO and Ikuhiko HAYASHI
Page 71(1093)
-
Fabrication of Titanium-Based Composites with Intermetallics Using Shock-Induced Reaction for Mixed Element Powders
Jung-Suk LEE, Kazuyuki HOKAMOTO,
Shigeru ITOH and Masahiro FUJITA
Page 76(1098)